Rolling Code 10-Channel UHF remote control (kit)

Shopping Cart

	Your Cart is Empty
	View Cart

Documentation in acrobat format (K181)

This kit is based on the cps180 (rolling code 4 channel remote control). It uses the same 4 button remote control, but you will see that 10 keypress combinations are actually supported – the 4 single buttons and 6 two keypress
combinations. This kit takes uses all 10 keypress combinations to operate 10 relays. The 12V relays can switch 120VAC at 1 Amp. Range up to 100'. Up to 15 transmitters can be learnt by one receiver. (includes 1 Transmitter)
(CPS181)

Quantity	Price
1 – 9	$72.19
10 – 99	$67.05
100 +	$64.82

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS181
Quantity Available:		3

Tell a Friend

This item is related to the items below.

UHF 434MHz Automicro 4 button (Transmitter only)

(DA16TX)

Quantity	Price
1 – 9	$22.29
10 – 99	$20.70
100 +	$20.01

Skill Level of Item:		(Assembled and Tested)
Product #		DA16TX
Quantity Available:		6

Rolling Code 2-Channel UHF Remote Control (kit)

This kit is a 2-channel version of CPS180, our 4-channel UHF Remote Control kit. We have simply removed two of the 4 channels from CPS180 and used a 2-button Transmitter unit. Up to 100' range. Up to 15 Transmitter units can be learnt by one Rx unit. (only 1 transmitter included). Although these relays are rated 12A/250VAC the PCB tracks will not carry that current. Please do not put more than 2A through these tracks. If you want to switch higher currect loads then you must jumper some wire between the terminal block pins and the relay pins. Receiver PCB size: L 3.32" x W 2.38" x H 0.88". (CPS157)

Quantity	Price
1 – 9	$52.33
10 – 99	$48.60
100 – 999	$46.98
1000 +	$39.95

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS157
Quantity Available:		5

Rolling Code 4-Channel UHF Remote (partially assembled)

State of the Art, with 4 channels either momentary or latching. Range up to 100'. Up to 15 transmitters can be learned by one receiver. (Includes 1 transmitter) 2 indicator LED's. PCB size: 3 3/8" x 3 1/16" 12VDC 6mA (at rest)(CPA180)

PLEASE NOTE: This is a partially assembled product. The daughter board must still be soldered onto the mother board. 13 solder points. Estimated time to finish: 5 minutes.

Quantity	Price
1 – 9	$70.74
10 – 99	$65.70
100 +	$63.51

Skill Level of Item:		(Partially Assembled)
Product #		CPA180
Quantity Available:		8

Rolling Code 4-Channel UHF Remote control (kit)

State of the Art, with 4 channels either momentary or latching. Range up to 100'. Up to 15 transmitters can be learnt by one receiver. (includes 1 Transmitter) 2 indicator LED's. PCB size: 3 3/8" x 3 1/16" 12VDC 6mA (at rest)(CPS180)

Quantity	Price
1 – 9	$58.14
10 – 99	$54.00
100 +	$52.20

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS180
Quantity Available:		11

You might also consider these items:

Infrared Remote control (12 channels) kit

12 channel relay board, each relay is individually controlled with included infrared remote control unit. Toggle or momentary. Over 50' range. PCB size: 4.8"x4.5". 12VDC.(CPS142)

Quantity	Price
1 – 9	$63.95
10 – 99	$59.40
100 +	$57.42

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS142
Quantity Available:		11

Multi Mode Timer kit

Uses microcontroller and crystal for accurate low cost timing. Seven different timing modes! Modes and delay ranges are set by DIP switches. Timing delays range between 255sec (1sec steps) and 42.5h(10min steps) PCB size: 1.9”x3.8” 12VDC (CPS141).

Quantity	Price
1 – 9	$23.26
10 – 99	$21.60
100 +	$20.88

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS141
Quantity Available:		19

Temperature Data Logger kit

This is an 8-pin microcontroller based circuit for temperature data logging via the serial port of any computer from between 1 and 4 remote digital
temperature sensors, DS18S20 or DS18S20 made by Dallas.

Features.
• provides realtime data via the serial port
• interfaces up to 4 x DS18S20 sensors
• accuracy to 0.5 degrees centigrade
• fahrenheit scale selected by a jumper
• no external power required
• data stream easily logged & processed
• over 200m distance for each sensor
PCB size: 1 1/2"x1 1/2" (CPS145)

Quantity	Price
1 – 9	$28.10
10 – 99	$26.10
100 +	$25.23

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS145
Quantity Available:		5

USB/Serial Port PIC Programm kit (ver E) (no zif socket)

This programmer (version E) connect to either a USB or serial port. Free software. Dozens of PIC's supported including 12c508, 16f84, 16F628 etc. For maximum programming flexibility a wide-slot 40 pin ZIF socket (not included) is recommended. Power supply: at least 16VDC (18VDC preferred) center positive required (power supply jack 5.5mm OD 2.5mm ID) at least 200mA.
Closeout item. Limited qty available. Reduced price!

Price: $52.20

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS149
Quantity Available:		7

TDA7052 Amplifier Module 1W

A 1W power amplifier building block designed to be part of a larger project. Ideal as a low power battery operated amplifier (from 3 to 15V) driving an 8 ohm speaker. The Philips TDA7052 is a general purpose amplifier. No heatsink needed. Short circuit protected. PCB size: 1.2" x 1.2" (30mm x 30mm)

Quantity	Price
1 – 9	$9.12
10 – 99	$8.64
100 +	$7.92

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS27
Quantity Available:		23

PIC Trainer

This kit teaches you how to use a microcontroller (uC) for measuring temperature (in either degrees F or deg C), humidity, as a counter, as a timer and for analog to digital conversion. The code to support all these functions is contained within the one programmed uC. The kit uses three plug-in units (supplied) to a motherboard which has an LCD on-board. (CPS75)

Quantity	Price
1 – 9	$58.14
10 – 99	$54.00
100 +	$52.20

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS75
Quantity Available:		3

Stereo VU Meter

Simple, low cost stereo VU meter. Two LM3915 dot/bar display driver ICs used to drive 2 rows of 10 LEDs(14 green,6 red)in a moving bar display. Each row of LEDs spans a power range of 0-30 dB in ten 3-dB steps. This VU meter indicates 'peak music power' when used with audio amp. Ideal add-on for any amplifier kit. PCB size: 65mm x 42mm.(2.6" x 1.65") This VU meter is capable of monitoring and displaying power levels present at the speaker terminals of a stereo audio power amplifier. Levels are displayed in ten discrete steps. This meter is not designed to give an accurate display of the power levels. It is designed to give an approximate visual indication of the audio power output of each channel. For many situations-disco, parties- this is all which is required: the flashing LED's add atmosphere to the situation. No calibration required. The kit is constructed on single-sided printed circuit board. It contains two identical circuits, one for each channel of the amplifier.(CPS89)

Quantity	Price
1 – 9	$17.10
10 – 99	$16.20
100 +	$14.85

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS89
Quantity Available:		9